Help with update cisco Template

[albadrius]

Hello Team,
i am struggling with update cisco cisco_ios_show_interfaces.textfsm & cisco_xr_show_interfaces.textfsm templates with adding Last Link Flapped to parsing, would you please assist with it , and if there is any guidance can use for updating the templates
Value LINK_FLAPPED (\w+)
^\s+${LINK_FLAPPED}\s+[Ll]ast\s+[Ll]ink\s+[Ff]lapped\s+{LINK_FLAPPED}\s*$$

cisco_ios_show_interfaces.textfsm

Value Required INTERFACE (\S+)
Value LINK_STATUS (.+?)
Value PROTOCOL_STATUS (.+?)
Value HARDWARE_TYPE ([\w ]+)
Value ADDRESS ([a-fA-F0-9]{4}.[a-fA-F0-9]{4}.[a-fA-F0-9]{4})
Value BIA ([a-fA-F0-9]{4}.[a-fA-F0-9]{4}.[a-fA-F0-9]{4})
Value DESCRIPTION (.+?)
Value IP_ADDRESS (\d+.\d+.\d+.\d+/\d+)
Value MTU (\d+)
Value DUPLEX (([Ff]ull|[Aa]uto|[Hh]alf|[Aa]-).?)
Value SPEED (.?)
Value MEDIA_TYPE (\S+(\s+\S+)?)
Value BANDWIDTH (\d+\s+\w+)
Value DELAY (\d+\s+\S+)
Value ENCAPSULATION (.+?)
Value LAST_INPUT (.+?)
Value LAST_OUTPUT (.+?)
Value LAST_OUTPUT_HANG (.+?)
Value QUEUE_STRATEGY (.+)
Value INPUT_RATE (\d+)
Value OUTPUT_RATE (\d+)
Value INPUT_PACKETS (\d+)
Value OUTPUT_PACKETS (\d+)
Value INPUT_ERRORS (\d+)
Value CRC (\d+)
Value ABORT (\d+)
Value OUTPUT_ERRORS (\d+)
Value LINK_FLAPPED (\w+)

Start
^\S+\s+is\s+.+?,\s+line\s+protocol.$$ -> Continue.Record
^${INTERFACE}\s+is\s+${LINK_STATUS},\s+line\s+protocol\s+is\s+${PROTOCOL_STATUS}\s$$
^\s+Hardware\s+is\s+${HARDWARE_TYPE} -> Continue
^.+address\s+is\s+${ADDRESS}\s+(bia\s+${BIA})\s*$$
^\s+Description:\s+${DESCRIPTION}\s*$$
^\s+Internet\s+address\s+is\s+${IP_ADDRESS}\s*$$
^\s+MTU\s+${MTU}.BW\s+${BANDWIDTH}.DLY\s+${DELAY},\s$$
^\s+Encapsulation\s+${ENCAPSULATION},.+$$
^\s+Last\s+input\s+${LAST_INPUT},\s+output\s+${LAST_OUTPUT},\s+output\s+hang\s+${LAST_OUTPUT_HANG}\s$$
^\s+Queueing\s+strategy:\s+${QUEUE_STRATEGY}\s*$$
^\s+${DUPLEX},\s+${SPEED},.+media\stype\sis\s${MEDIA_TYPE}$$
^.input\s+rate\s+${INPUT_RATE}.+$$
^.output\s+rate\s+${OUTPUT_RATE}.+$$
^\s+${INPUT_PACKETS}\s+packets\s+input,\s+\d+\s+bytes,\s+\d+\s+no\s+buffer\s$$
^\s+${INPUT_ERRORS}\s+input\s+errors,\s+${CRC}\s+CRC,\s+\d+\s+frame,\s+\d+\s+overrun,\s+\d+\s+ignored\s$$
^\s+${INPUT_ERRORS}\s+input\s+errors,\s+${CRC}\s+CRC,\s+\d+\s+frame,\s+\d+\s+overrun,\s+\d+\s+ignored,\s+${ABORT}\s+abort\s*$$
^\s+${OUTPUT_PACKETS}\s+packets\s+output,\s+\d+\s+bytes,\s+\d+\s+underruns\s*$$
^\s+${OUTPUT_ERRORS}\s+output\s+errors,\s+\d+\s+collisions,\s+\d+\s+interface\s+resets\s*$$
^\s+${LINK_FLAPPED}\s+[Ll]ast\s+[Ll]ink\s+[Ff]lapped\s+{LINK_FLAPPED}\s*$$

Capture time-stamp if vty line has command time-stamping turned on

^Load\s+for\s+
^Time\s+source\s+is

---

Router Output Ex

---

FourHundredGigE0/4/0/23 is up, line protocol is up
Interface state transitions: 39
Dampening enabled: penalty 0, not suppressed
half-life: 5 reuse: 1000
suppress: 2000 max-suppress-time: 20
restart-penalty: 0
Hardware is FourHundredGigE, address is b368.1481.412c (bia b402.1631.429c)
Description: Testckt_AAV
Internet address is Unknown
MTU 1500 bytes, BW 400000000 Kbit (Max: 400000000 Kbit)
reliability 255/255, txload 33/255, rxload 6/255
Encapsulation ARPA,
Full-duplex, 400000Mb/s, 400GBASE-FR4, link type is force-up
output flow control is off, input flow control is off
Carrier delay (up) is 10 msec
loopback not set,
Last link flapped 2w3d
Last input 00:00:00, output 00:00:00
Last clearing of "show interface" counters 15w1d
30 second input rate 9694905000 bits/sec, 2303525 packets/sec
30 second output rate 52100411000 bits/sec, 5856909 packets/sec
11231804468431 packets input, 6174346737907636 bytes, 0 total input drops
0 drops for unrecognized upper-level protocol
Received 2 broadcast packets, 100622430 multicast packets
0 runts, 0 giants, 0 throttles, 0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
20033304661016 packets output, 20951130076401259 bytes, 0 total output drops
Output 3 broadcast packets, 93256553 multicast packets
0 output errors, 0 underruns, 0 applique, 0 resets
0 output buffer failures, 0 output buffers swapped out
8 carrier transitions

[mjbear]

Hello Team, i am struggling with update cisco cisco_ios_show_interfaces.textfsm & cisco_xr_show_interfaces.textfsm templates with adding Last Link Flapped to parsing, would you please assist with it , and if there is any guidance can use for updating the templates

Hello @albadrius
Were you able to solve for your goal?

(If yes this is still an open item,) Would you be able to update your post with all of your "code" or "output" in code fences (which preserve whitespace)?